LK Automation Limited
Brand:
MITSUBISHI
MR-J2S-55KB4 | MITSUBISHI SSCNET interface servo amplifier MR-J2S-55KB4
MITSUBISHI MR-J2S-55KB4 Manual And Instructions
MR-J2S-55KB4 datasheetPDF datasheet
MR-J2S-55KB4 SUPPLEMENTARY INSTRUCTION MANUAL
MITSUBISHI MR-J2S-55KB4 Product information and technical parameters：
Brand: MITSUBISHI
Name: SSCNET interface servo amplifier
Model: MR-J2S-55KB4
MITSUBISHI general purpose AC servo amplifier MELSERVO-J2-Super series.
Rated output: 55.0kw.
SSCNET interface.
Voltage: 3 phase AC400V.
Complete synchronization system with SSCNET high speed serial communication,
The communication cycle between the controller and the servo amplifier is the longest 0.888ms.
Such systems will be able to provide high reliability and high performance.
When connecting the servo system with SSCNET,
In the motion system, the parameters of the servo amplifier and the acquisition of the data will be displayed on the motion controller.
Connect a dedicated cable with an amplifier and a controller to form a SSCNET system.
This simple connection method reduces the routing time and helps to prevent noise.
Even in the MELSERVO-J2-SUPER series products using high resolution coding standards, the command frequency is no limit.
It is only necessary to add a battery on the servo amplifier, which can form the absolute value system.
Currently there are more than 1000000 high reliability SSCNET servo amplifier networks in use.
...More relevant models >>>>
MR-J2S-55KB4 datasheetPDF datasheet
MR-J2S-55KB4 SUPPLEMENTARY INSTRUCTION MANUAL
MITSUBISHI MR-J2S-55KB4 Product information and technical parameters：
Brand: MITSUBISHI
Name: SSCNET interface servo amplifier
Model: MR-J2S-55KB4
MITSUBISHI general purpose AC servo amplifier MELSERVO-J2-Super series.
Rated output: 55.0kw.
SSCNET interface.
Voltage: 3 phase AC400V.
Complete synchronization system with SSCNET high speed serial communication,
The communication cycle between the controller and the servo amplifier is the longest 0.888ms.
Such systems will be able to provide high reliability and high performance.
When connecting the servo system with SSCNET,
In the motion system, the parameters of the servo amplifier and the acquisition of the data will be displayed on the motion controller.
Connect a dedicated cable with an amplifier and a controller to form a SSCNET system.
This simple connection method reduces the routing time and helps to prevent noise.
Even in the MELSERVO-J2-SUPER series products using high resolution coding standards, the command frequency is no limit.
It is only necessary to add a battery on the servo amplifier, which can form the absolute value system.
Currently there are more than 1000000 high reliability SSCNET servo amplifier networks in use.
Fiber length: 50 meters.
SSCNET III cable (long distance optical fiber, high bending life).
Joints for CN1A and CN1B. Servo motor series: low inertia, medium / high power.
Rated output: 45.0kw.
Rated speed: 2000r/min.
Electromagnetic brake: No.
Shaft end specification: Standard (straight axis).
Voltage: 400V level MITSUBISHI MR-J2S-55KB4.
Features: low inertia has low medium and high speed three models, suitable for different applications as a standard, 30KW and above servo motor can be installed flange or bracket MR-J2S-55KB4
IP level: IP44.
Application example:
1, injection molding machine.
2, semiconductor manufacturing equipment.
3, large material handling system.
4, stamping machine.
Abundant motor product line can optimize the performance of the machine MITSUBISHI MR-J2S-55KB4.
Has a rich motor product line including a rotary servo motor, linear servo motor and direct drive motor. The length of the line: 10M.
IP level: IP65.
Direct type.
The cable is not shielded.
Bending life: standard.
Connector kit for motor electromagnetic brake.
Cable for electromagnetic brake, for HF-KP/HF-MP series (motor shaft with side extraction). MITSUBISHI motor universal AC servo amplifier MELSERVO-J3 series MITSUBISHI MR-J2S-55KB4.
Rated output: 1.0kw.
Interface type: SSCNET type III fiber communication.
Special specification: suitable for direct drive servo motor.
Power specification: three phase AC200V.
Direct drive system suitable for high speed and high precision!
High speed operation can be realized by direct drive (2m/s), and the traditional mechanical transmission can not achieve such a high speed.
The full closed loop control can be realized by using the position feedback signal from the load side encoder, such as the linear encoder.
The use of a flexible linear servo motor drive components can make the system more compact structure MR-J2S-55KB4.
The primary side of the linear servo motor (motor coil) is sliding along the secondary side (permanent magnet) of the motor,
So linear servo motor is especially suitable for large range of appliccations MR-J2S-55KB4. In addition, linear servo motor can be connected in series,
Especially for large systems in two axes for high precision synchronous operation.
SSCNET III cable (long distance optical fiber, high bending life).
Joints for CN1A and CN1B. Servo motor series: low inertia, medium / high power.
Rated output: 45.0kw.
Rated speed: 2000r/min.
Electromagnetic brake: No.
Shaft end specification: Standard (straight axis).
Voltage: 400V level MITSUBISHI MR-J2S-55KB4.
Features: low inertia has low medium and high speed three models, suitable for different applications as a standard, 30KW and above servo motor can be installed flange or bracket MR-J2S-55KB4
IP level: IP44.
Application example:
1, injection molding machine.
2, semiconductor manufacturing equipment.
3, large material handling system.
4, stamping machine.
Abundant motor product line can optimize the performance of the machine MITSUBISHI MR-J2S-55KB4.
Has a rich motor product line including a rotary servo motor, linear servo motor and direct drive motor. The length of the line: 10M.
IP level: IP65.
Direct type.
The cable is not shielded.
Bending life: standard.
Connector kit for motor electromagnetic brake.
Cable for electromagnetic brake, for HF-KP/HF-MP series (motor shaft with side extraction). MITSUBISHI motor universal AC servo amplifier MELSERVO-J3 series MITSUBISHI MR-J2S-55KB4.
Rated output: 1.0kw.
Interface type: SSCNET type III fiber communication.
Special specification: suitable for direct drive servo motor.
Power specification: three phase AC200V.
Direct drive system suitable for high speed and high precision!
High speed operation can be realized by direct drive (2m/s), and the traditional mechanical transmission can not achieve such a high speed.
The full closed loop control can be realized by using the position feedback signal from the load side encoder, such as the linear encoder.
The use of a flexible linear servo motor drive components can make the system more compact structure MR-J2S-55KB4.
The primary side of the linear servo motor (motor coil) is sliding along the secondary side (permanent magnet) of the motor,
So linear servo motor is especially suitable for large range of appliccations MR-J2S-55KB4. In addition, linear servo motor can be connected in series,
Especially for large systems in two axes for high precision synchronous operation.
...More relevant models >>>>