LK Automation Limited
Brand:
MITSUBISHI
QE8WH4VT | MITSUBISHI Special transformer QE8WH4VT
MITSUBISHI QE8WH4VT Manual And Instructions
QE8WH4VT datasheetPDF datasheet
MITSUBISHI QE8WH4VT Product information and technical parameters：
Brand: MITSUBISHI
Name: Special transformer
Model: QE8WH4VT
E81WH4W, QE83WH4W special transformer.
Power measurement module product group capable of simply measuring various energy information.
With only one module can be used to measure and power consumption (consumption and regeneration), reactive power, current, voltage, power, power factor and frequency of all kinds of detailed information.
No ladder program can continue to monitor the minimum and maximum values, can also perform 2 types of upper / lower limit alarm.
Only in the ON state can be used to measure the output of the output device.
Therefore, the amount of electricity and the quantity of electricity in the unit of the beat can be obtained during the operation of the equipment.
3 phase 3 wire products can be used to measure up to 4 circuits in one slot,
3 phase 4 wire products can be used to measure up to 3 circuits,
So the electrical energy measurement can be carried out in a small space by the multi circuit products.
For example, a module can be used to measure other loads from the control panel trunk.
In addition, Works2 GX (version 1.90U and higher) can be used to easily set parameters.
...More relevant models >>>>
QE8WH4VT datasheetPDF datasheet
MITSUBISHI QE8WH4VT Product information and technical parameters：
Brand: MITSUBISHI
Name: Special transformer
Model: QE8WH4VT
E81WH4W, QE83WH4W special transformer.
Power measurement module product group capable of simply measuring various energy information.
With only one module can be used to measure and power consumption (consumption and regeneration), reactive power, current, voltage, power, power factor and frequency of all kinds of detailed information.
No ladder program can continue to monitor the minimum and maximum values, can also perform 2 types of upper / lower limit alarm.
Only in the ON state can be used to measure the output of the output device.
Therefore, the amount of electricity and the quantity of electricity in the unit of the beat can be obtained during the operation of the equipment.
3 phase 3 wire products can be used to measure up to 4 circuits in one slot,
3 phase 4 wire products can be used to measure up to 3 circuits,
So the electrical energy measurement can be carried out in a small space by the multi circuit products.
For example, a module can be used to measure other loads from the control panel trunk.
In addition, Works2 GX (version 1.90U and higher) can be used to easily set parameters.
Master station.
Province distribution network module in cabinet and device.
Link to connect the 64 stations when the fastest scanning time for 1.2ms (rate 2.5Mbps).
According to the transmission distance, the transmission rate is selected from 2.5Mbps, 625kbps and 156kbps.
CC-Link/LT from the station does not need any parameter settings MITSUBISHI QE8WH4VT.
Only need to set up the transmission speed in the master module, you can use the remote I/O QE8WH4VT
QJ61CL12 can be used as the main station of CC-Link/LT.For common cathode input module and drain type output module (standard type).For common cathode input module (2 line type).Positioning: 3 axis, built-in counter function, open collector output type.
Control unit: pulse MITSUBISHI QE8WH4VT.
Number of location data: 1/ axis.
Maximum output pulse: 100Kpps.
Counter: 3 channels.
100Kpps.
Counter input signal: DV5~24V.
40 pin connector.
Positioning control using encoder feedback, especially suitable for conveying system and processing machinery, etc..
In the 1 single module, the 3 axis positioning function and the 3 channel counter function are integrated.
Positioning module, high-speed counter module combined as a whole,
Can effectively use the board slot and save space MITSUBISHI QE8WH4VT. RS232 cable for connecting cables and 3M, CPU.32 point connector for welding (37 pin D-Sub connector).BASIC program execution module.
RS-232.
2 channel.
Ultra high speed processing, production time is shortened, better performance.
As applications become larger and more complex, it is necessary to shorten the system operation cycle time.
The operation period can be shortened by the super high basic operation speed 1.9ns.
In addition to achieve in the past with the control of single-chip high-speed control,
The system performance can be improved by reducing the total scan time,
To prevent any possible performance bias QE8WH4VT.
The position signal of the first axis servo amplifier, which is used on the motion CPU, is used as a trigger,
Starting from the programmable controller CPU to the second axis servo amplifier,
Time to output speed command of servo amplifier QE8WH4VT.
This time is the index of data transmission speed between CPU.
Province distribution network module in cabinet and device.
Link to connect the 64 stations when the fastest scanning time for 1.2ms (rate 2.5Mbps).
According to the transmission distance, the transmission rate is selected from 2.5Mbps, 625kbps and 156kbps.
CC-Link/LT from the station does not need any parameter settings MITSUBISHI QE8WH4VT.
Only need to set up the transmission speed in the master module, you can use the remote I/O QE8WH4VT
QJ61CL12 can be used as the main station of CC-Link/LT.For common cathode input module and drain type output module (standard type).For common cathode input module (2 line type).Positioning: 3 axis, built-in counter function, open collector output type.
Control unit: pulse MITSUBISHI QE8WH4VT.
Number of location data: 1/ axis.
Maximum output pulse: 100Kpps.
Counter: 3 channels.
100Kpps.
Counter input signal: DV5~24V.
40 pin connector.
Positioning control using encoder feedback, especially suitable for conveying system and processing machinery, etc..
In the 1 single module, the 3 axis positioning function and the 3 channel counter function are integrated.
Positioning module, high-speed counter module combined as a whole,
Can effectively use the board slot and save space MITSUBISHI QE8WH4VT. RS232 cable for connecting cables and 3M, CPU.32 point connector for welding (37 pin D-Sub connector).BASIC program execution module.
RS-232.
2 channel.
Ultra high speed processing, production time is shortened, better performance.
As applications become larger and more complex, it is necessary to shorten the system operation cycle time.
The operation period can be shortened by the super high basic operation speed 1.9ns.
In addition to achieve in the past with the control of single-chip high-speed control,
The system performance can be improved by reducing the total scan time,
To prevent any possible performance bias QE8WH4VT.
The position signal of the first axis servo amplifier, which is used on the motion CPU, is used as a trigger,
Starting from the programmable controller CPU to the second axis servo amplifier,
Time to output speed command of servo amplifier QE8WH4VT.
This time is the index of data transmission speed between CPU.
...More relevant models >>>>
Related download