LK Automation Limited LK Automation Limited
Brand: MITSUBISHI
Go Back >> Product Catalogues
MR-J4W2-1010B | MITSUBISHI Multi axis servo drive MR-J4W2-1010B
MITSUBISHI MR-J4W2-1010B Manual And Instructions
MR-J4W2-1010B datasheetPDF datasheet

MITSUBISHI MR-J4W2-1010B Product information and technical parameters:
Brand: MITSUBISHI
Name: Multi axis servo drive
Model: MR-J4W2-1010B
Multi axis integrated servo amplifier.
MITSUBISHI general AC servo amplifier MELSERVO-J4 series.
Axis number: 2 axis.
Rated output A axis (Note 1): 1.0kw.
Rated output B axis (Note 1): 1.0kw.
Interface: SSCNET III /H.
Note the 1:A axis, B axis, C axis indicates the name of a type of multi axis servo amplifier axis. The C axis represents the 3 axis one type servo amplifier.
Support SSCNET III /H. 3 axis one type servo amplifier capable of driving 3 servo motors through a single module.
More energy saving, space saving, less wiring, low cost.
Inherited the high performance and high reliability.
Will, as always, adhere to and uphold the excellent quality of MELSERVO.
MR-J4 has inherited the excellent design of existing products.
Its essence to its dregs, create advantage and cost effective utilization rate,
Make full use of renewable resources, to create a new product.

Drive: MR-H_ACN series CC-LINK features.
Rated output: 5.0KW.
The test system is composed of two parts, namely, the servo driver, the motor system and the host computer.
The host computer sends the speed command signal to the servo driver,
Servo drives start to run in accordance with the instructions MITSUBISHI MR-J4W2-1010B.
In the course of operation, the running data of the servo system is collected by the host computer and the data acquisition circuit,
And carries on the preservation, the analysis and the display to the data MR-J4W2-1010B Because the motor is not loaded in this test system,
So compared with the previous two kinds of testing systems, the system has a relatively small volume,
And the measurement and control circuit of the system is relatively simple,
But it also makes the system can not simulate the actual operation of the servo drive MITSUBISHI MR-J4W2-1010B.
Usually, such testing system is only used to test the rotational speed and angular displacement of the tested system under no-load condition,
And can not carry on the comprehensive and accurate test to the servo drive. Motor series: medium inertia, medium power.
Rated output power: 5 MITSUBISHI MR-J4W2-1010B. 0kw.
Rated speed: 2000r/min.
Whether to bring the brakes: with.
Shaft end: Standard (straight).
Power supply: 400V type.
Protection level: IP65 (IP67).
Features: medium inertia from low speed to high speed three modes for selection, suitable for different applications.
Application examples: transmission machinery, robots, X-Y working platform.
High resolution encoder 131072p/rev (17 bit).
The encoder with high resolution ensures excellent performance and stability at low speed.
All motor dimensions are the same as before and all are compatible with the wiring. Motor series: medium inertia, medium power.
Rated output power: 7.0kw.
Rated speed: 2000r/min.
Whether to bring the brakes: with.
Shaft end: Standard (straight).
Protection level: IP65 (IP67).
Features: medium inertia from low speed to high speed three modes for selection, suitable for different applications MR-J4W2-1010B.
Application examples: transmission machinery, robots, X-Y working platform.
High resolution encoder 131072p/rev (17 bit).
The encoder with high reesolution ensures excellent performance and stability at low speed MR-J4W2-1010B.
All motor dimensions are the same as before and all are compatible with the wiring.


...More relevant models >>>>