LK Automation Limited LK Automation Limited
Brand: MITSUBISHI
Go Back >> Product Catalogues
MR-J4-500A-RJ | MITSUBISHI Servo driver MR-J4-500A-RJ
MITSUBISHI MR-J4-500A-RJ Manual And Instructions
MR-J4-500A-RJ datasheetPDF datasheet

MITSUBISHI MR-J4-500A-RJ Product information and technical parameters:
Brand: MITSUBISHI
Name: Servo driver
Model: MR-J4-500A-RJ
1 axis servo amplifier.
MITSUBISHI general AC servo amplifier MELSERVO-J4 series.
Rated output: 5.0kw.
Interface: General purpose.
Power supply: three phase AC200V.
Special specification: full closed loop control 4 wire / device end encoder ABZ phase input corresponding support function security unit, support positioning mode.
Servo amplifier supporting universal interface.
Servo amplifier for universal interface.
Speed / torque control of position control and analog voltage command can be carried out by using pulse train command.
Support Max instruction pulse frequency 4 Mpulses/s.
Improve mechanical properties by high performance motor.
By improving the resolution and processing speed of the encoder,
The rotating servo motor has higher precision and better performance of rotation.
Only open a key type of adjustment function, can be carried out including mechanical resonance filter, high end seismic control II, low pass filter servo gain adjustment.
Easily start advanced seismic function, it can maximize the mechanical properties.
It can automatically adjust the required response settings automatically.

MITSUBISHI motor universal AC servo amplifier MELSERVO-J3 series.
Rated output: 5.0kw.
Interface type: SSCNET type III fiber communication.
Special specification: suitable for linear servo motor.
Power specification: three phase AC400V.
More advanced real-time automatic tuning by setting response values,
Including the position gain and the gain of speed, all the gain can be adjusted automatically MITSUBISHI MR-J4-500A-RJ MR-J4-500A-RJ
32 segment response level can be set.
Advanced vibration suppression control.
An optimal vibration control filter value is automatically set by the automatic tuning function to effectively suppress the vibration of the 100Hz frequency that occurs when the driving part stops.
The automatic tuning function can effectively restrain the vibration of the end of the mechanical arm and reduce the residual vibration in the machine MITSUBISHI MR-J4-500A-RJ. Controller to amplifier adapterType: HF-SE servo motor, medium inertia power.
Rated output power: 1.5kw.
Rated speed: 2000r/min.
Electromagnetic brake: No.
Oil seal: No.
Servo motor can make control speed, position accuracy is very accurate,
The voltage signal can be converted to torque and speed to drive the control object MITSUBISHI MR-J4-500A-RJ.
Servo motor rotor speed is controlled by the input signal, and can quickly response,
In an automatic control system, used as an actuator,
With electromechanical time constant, high linearity, initiating voltage characteristics,
The signal can be converted into a motor shaft on the angular displacement or angular velocity output.
Divided into DC and AC servo motor two major categories, the main features are,
When the signal voltage is zero, the rotation speed increases with the increase of torque.
Servo amplifier terminals are used to reduce the required wiring time.
The connector is located in front of the servo amplifier, which is convenient for cable connection.
The gain adjustment can be easily carried out by the real-time automatic tuning function.
Wide use.
Machining equipment and machine tool feed.
Used for food, packaging equipment and feeding device.
For textile machinery, etc..
Can improve the performance of equipment.
High performance and easy to operate, reduce work load.
Enhanced system cost performance.
High performance,, high precision positioning (servo motor encoder resolution: 131072) MR-J4-500A-RJ.
High response.
Suppression of vibration by adaptive vibration suppression control.
Using personal computer and servo setup software to optimize tuning.
Has 2 types of interfaces:
Position control and speed control with pulse train interface MR-J4-500A-RJ.
The analog input interface is used for speed control and torque control.


...More relevant models >>>>