LK Automation Limited
Brand:
MITSUBISHI
MR-J3-70T | MITSUBISHI CC-Link communication driver MR-J3-70T
MITSUBISHI MR-J3-70T Manual And Instructions
MR-J3-70T datasheetPDF datasheet
MR-J3-70T CC-LinkINSTRUCTION MANUAL
MR-J3-70T General-Purpose InterfaceINSTRUCTION MANUAL
MITSUBISHI MR-J3-70T Product information and technical parameters：
Brand: MITSUBISHI
Name: CC-Link communication driver
Model: MR-J3-70T
MITSUBISHI motor universal AC servo amplifier MELSERVO-J3 series.
Rated output: 0.75kw.
Interface type: CC-Link communication type (built-in positioning function).
Power specification: single phase AC200V.
Positioning operation by setting position and rotational speed data in the positioning table and receiving the start signal from the main controller.
The setting of the position and speed of the positioning table, as well as the start and stop operation can be completed through CC-Link communication.
By using the MR-J3-D01 extension IO unit, the DI/O instruction can be used to select and locate the table.
(CC-Link can not be used for MR-J3-D01 communications).
With built-in positioning function of the servo amplifier, can be set through the CC-Link communications and speed data. (corresponding to the CC-Link version: Ver.1.10)
Can be achieved through the CC-Link communications to start, stop and monitoring and other operations.
Serial communication reduce wiring.
Distributed servo control system can be built by CC-Link communication.
The parameters of unit MR-PRU03 (optional) the parameter setting, operation and monitoring more convenient.
The servo amplifier can be used for speed control operation.
When the two stations are occupied, the speed can be set directly by the remote register.
...More relevant models >>>>
MR-J3-70T datasheetPDF datasheet
MR-J3-70T CC-LinkINSTRUCTION MANUAL
MR-J3-70T General-Purpose InterfaceINSTRUCTION MANUAL
MITSUBISHI MR-J3-70T Product information and technical parameters：
Brand: MITSUBISHI
Name: CC-Link communication driver
Model: MR-J3-70T
MITSUBISHI motor universal AC servo amplifier MELSERVO-J3 series.
Rated output: 0.75kw.
Interface type: CC-Link communication type (built-in positioning function).
Power specification: single phase AC200V.
Positioning operation by setting position and rotational speed data in the positioning table and receiving the start signal from the main controller.
The setting of the position and speed of the positioning table, as well as the start and stop operation can be completed through CC-Link communication.
By using the MR-J3-D01 extension IO unit, the DI/O instruction can be used to select and locate the table.
(CC-Link can not be used for MR-J3-D01 communications).
With built-in positioning function of the servo amplifier, can be set through the CC-Link communications and speed data. (corresponding to the CC-Link version: Ver.1.10)
Can be achieved through the CC-Link communications to start, stop and monitoring and other operations.
Serial communication reduce wiring.
Distributed servo control system can be built by CC-Link communication.
The parameters of unit MR-PRU03 (optional) the parameter setting, operation and monitoring more convenient.
The servo amplifier can be used for speed control operation.
When the two stations are occupied, the speed can be set directly by the remote register.
Servo amplifier side connector.Multi axis integrated servo amplifier.
MITSUBISHI general AC servo amplifier MELSERVO-J4 series.
Axis number: 3 axis.
Rated output A axis (Note 1): 0.4kw.
Rated output B axis (Note 1): 0.4kw.
Rated output C axis (Note 1): 0.4kw.
Interface: SSCNET III /H.
Note the 1:A axis, B axis, C axis indicates the name of a type of multi axis servo amplifier axis MITSUBISHI MR-J3-70T MR-J3-70T The C axis represents the 3 axis one type servo amplifier.
Support SSCNET III /H. 3 axis one type servo amplifier capable of driving 3 servo motors through a single module.
More energy saving, space saving, less wiring, low cost.
Inherited the high performance and high reliability.
Will, as always, adhere to and uphold the excellent quality of MELSERVO MITSUBISHI MR-J3-70T.
MR-J4 has inherited the excellent design of existing products.
Its essence to its dregs, create advantage and cost effective utilization rate,
Make full use of renewable resources, to create a new product. Drive: MR-H_ACN series CC-LINK features.
Rated output: 15KW.
The test system is composed of two parts, namely, the servo driver, the motor system and the host computer MITSUBISHI MR-J3-70T.
The host computer sends the speed command signal to the servo driver,
Servo drives start to run in accordance with the instructions.
In the course of operation, the running data of the servo system is collected by the host computer and the data acquisition circuit,
And carries on the preservation, the analysis and the display to the data. Because the motor is not loaded in this test system,
So compared with the previous two kinds of testing systems, the system has a relatively small volume,
And the measurement and control circuit of the system is relatively simple,
But it also makes the system can not simulate the actual operation of the servo drive.
Usually, such testing systtem is only used to test the rotational speed and angular displacement of the tested system under no-load condition,
And can not carry on the comprehensive and accurate test to the servo drive MR-J3-70T. Cable length: 20m.
For MR-J2S-700A (4) /CP/CLL or less MR-J3-70T.
Encoder for HC-SFS; HC-LFS; HC-RFS; 2000r/min HA-LFS; HC-UFS servo motor.
-H products have a long flex life.
Coding is not resistant to oil.
MITSUBISHI general AC servo amplifier MELSERVO-J4 series.
Axis number: 3 axis.
Rated output A axis (Note 1): 0.4kw.
Rated output B axis (Note 1): 0.4kw.
Rated output C axis (Note 1): 0.4kw.
Interface: SSCNET III /H.
Note the 1:A axis, B axis, C axis indicates the name of a type of multi axis servo amplifier axis MITSUBISHI MR-J3-70T MR-J3-70T The C axis represents the 3 axis one type servo amplifier.
Support SSCNET III /H. 3 axis one type servo amplifier capable of driving 3 servo motors through a single module.
More energy saving, space saving, less wiring, low cost.
Inherited the high performance and high reliability.
Will, as always, adhere to and uphold the excellent quality of MELSERVO MITSUBISHI MR-J3-70T.
MR-J4 has inherited the excellent design of existing products.
Its essence to its dregs, create advantage and cost effective utilization rate,
Make full use of renewable resources, to create a new product. Drive: MR-H_ACN series CC-LINK features.
Rated output: 15KW.
The test system is composed of two parts, namely, the servo driver, the motor system and the host computer MITSUBISHI MR-J3-70T.
The host computer sends the speed command signal to the servo driver,
Servo drives start to run in accordance with the instructions.
In the course of operation, the running data of the servo system is collected by the host computer and the data acquisition circuit,
And carries on the preservation, the analysis and the display to the data. Because the motor is not loaded in this test system,
So compared with the previous two kinds of testing systems, the system has a relatively small volume,
And the measurement and control circuit of the system is relatively simple,
But it also makes the system can not simulate the actual operation of the servo drive.
Usually, such testing systtem is only used to test the rotational speed and angular displacement of the tested system under no-load condition,
And can not carry on the comprehensive and accurate test to the servo drive MR-J3-70T. Cable length: 20m.
For MR-J2S-700A (4) /CP/CLL or less MR-J3-70T.
Encoder for HC-SFS; HC-LFS; HC-RFS; 2000r/min HA-LFS; HC-UFS servo motor.
-H products have a long flex life.
Coding is not resistant to oil.
...More relevant models >>>>