LK Automation Limited
Brand:
MITSUBISHI
FX3G-CNV-ADP | MITSUBISHI Adapter for special adapter connections FX3G-CNV-ADP
MITSUBISHI FX3G-CNV-ADP Manual And Instructions
FX3G-CNV-ADP datasheetPDF datasheet
FX3G-CNV-ADP INSTALLATION MANUAL
MITSUBISHI FX3G-CNV-ADP Product information and technical parameters：
Brand: MITSUBISHI
Name: Adapter for special adapter connections
Model: FX3G-CNV-ADP
Use FX3S-CNV-ADP when connecting to the left of the basic unit of the FX3SA, FX3U, and FX3S.
...More relevant models >>>>
FX3G-CNV-ADP datasheetPDF datasheet
FX3G-CNV-ADP INSTALLATION MANUAL
MITSUBISHI FX3G-CNV-ADP Product information and technical parameters：
Brand: MITSUBISHI
Name: Adapter for special adapter connections
Model: FX3G-CNV-ADP
Use FX3S-CNV-ADP when connecting to the left of the basic unit of the FX3SA, FX3U, and FX3S.
Analog output expansion board (1 channel).Max input / output points: 10 points.
Power supply voltage: 24VDC.
Input points: 6 points.
Output points: 4 points.
Output type: relay.
Power consumption (W): 6.
Weight (kg):0.22.
Size (WxHxD) mm:60x90x49.
Host has 10 points (6I/4O), 14 points (8I/6O), 20 points (12I/8O), 30 points (16I/14O) of 4 types MITSUBISHI FX3G-CNV-ADP.
This type of PLC is mainly used in all of the digital input, digital output control point of the device FX3G-CNV-ADP
Can be directly connected to the 220V city power, built-in 8K step EEPROM memory, no battery, easy to maintain.
The series transistor output (MT) of the PLC, can be output 2 100KHz pulse, direct drive servo or stepper motor.
The series PLC can not be brought with the expansion module, but can be installed by the BD board to extend a small amount of I/O MITSUBISHI FX3G-CNV-ADP.
The series 1N through the installation of BD series PLC board, can achieve RS232, RS485, RS422 communication.
All equipment is digital input and output point.
The total I/O points are not more than 30 points, and the input points are less than 16, the output points are less than 14.
Its MT series of PLC can drive 2 way servo or stepper, commonly used in the control system for a simple manipulator MITSUBISHI FX3G-CNV-ADP. "Max input / output points: 10 points.
Supply voltage: 100 - 240VAC.
Input points: 6 points.
Output points: 4 points.
Output type: Transistor (source).
Power consumption (W): 19.
Weight (kg):0.3.
Size (WxHxD) mm:60x90x75.
All equipment is digital input and output point.
The total I/O points are not more than 30 points, and the input points are less than 16, the output points are less than 14.
Its MT series of PLC can drive 2 way servo or stepper, commonly used in the control systeem for a simple manipulator FX3G-CNV-ADP.
MITSUBISHI FX1S series PLC is suitable for the smallest package,
It is the preferred target for low cost users to seek powerful control over a limited range of I/0.
FX1S provides up to 30 I/O points, and cann be transmitted through serial communication data,
MT models also have the ability to locate, widely used in a variety of small mechanical equipment FX3G-CNV-ADP. "
Power supply voltage: 24VDC.
Input points: 6 points.
Output points: 4 points.
Output type: relay.
Power consumption (W): 6.
Weight (kg):0.22.
Size (WxHxD) mm:60x90x49.
Host has 10 points (6I/4O), 14 points (8I/6O), 20 points (12I/8O), 30 points (16I/14O) of 4 types MITSUBISHI FX3G-CNV-ADP.
This type of PLC is mainly used in all of the digital input, digital output control point of the device FX3G-CNV-ADP
Can be directly connected to the 220V city power, built-in 8K step EEPROM memory, no battery, easy to maintain.
The series transistor output (MT) of the PLC, can be output 2 100KHz pulse, direct drive servo or stepper motor.
The series PLC can not be brought with the expansion module, but can be installed by the BD board to extend a small amount of I/O MITSUBISHI FX3G-CNV-ADP.
The series 1N through the installation of BD series PLC board, can achieve RS232, RS485, RS422 communication.
All equipment is digital input and output point.
The total I/O points are not more than 30 points, and the input points are less than 16, the output points are less than 14.
Its MT series of PLC can drive 2 way servo or stepper, commonly used in the control system for a simple manipulator MITSUBISHI FX3G-CNV-ADP. "Max input / output points: 10 points.
Supply voltage: 100 - 240VAC.
Input points: 6 points.
Output points: 4 points.
Output type: Transistor (source).
Power consumption (W): 19.
Weight (kg):0.3.
Size (WxHxD) mm:60x90x75.
All equipment is digital input and output point.
The total I/O points are not more than 30 points, and the input points are less than 16, the output points are less than 14.
Its MT series of PLC can drive 2 way servo or stepper, commonly used in the control systeem for a simple manipulator FX3G-CNV-ADP.
MITSUBISHI FX1S series PLC is suitable for the smallest package,
It is the preferred target for low cost users to seek powerful control over a limited range of I/0.
FX1S provides up to 30 I/O points, and cann be transmitted through serial communication data,
MT models also have the ability to locate, widely used in a variety of small mechanical equipment FX3G-CNV-ADP. "
...More relevant models >>>>
Related download