LK Automation Limited
Brand:
MITSUBISHI
FR-F740-S560K-CHT | MITSUBISHI 3 phase 400V converter FR-F740-S560K-CHT
MITSUBISHI FR-F740-S560K-CHT Manual And Instructions
FR-F740-S560K-CHT datasheetPDF datasheet
FR-F740-S560K-CHT AppliedInstruction manual
FR-F740-S560K-CHT BASICInstruction manual
FR-F740-S560K-CHT TECHNICAL MANUAL
MITSUBISHI FR-F740-S560K-CHT Product information and technical parameters：
Brand: MITSUBISHI
Name: 3 phase 400V converter
Model: FR-F740-S560K-CHT
MITSUBISHI inverter FR-F740 series.
Voltage level: three phase 400V.
Frequency converter capacity: 560KW.
The main circuit of the inverter can be divided into two categories in general: voltage type is the voltage source of the DC converter for AC inverter,
The filtering of the DC circuit is the capacitance; the current mode is the DC conversion of the current source to the AC inverter,
The DC loop filter is the inductor.
Why is the frequency of the inverter voltage proportional to the change?
The electromagnetic torque of any motor is the result of the interaction between the current and the magnetic flux, the current is not allowed to exceed the rated value, otherwise it will cause the heating of the motor.
Therefore, if the magnetic flux decreases, the electromagnetic torque will decrease, which leads to the reduction of the load carrying capacity.
...More relevant models >>>>
FR-F740-S560K-CHT datasheetPDF datasheet
FR-F740-S560K-CHT AppliedInstruction manual
FR-F740-S560K-CHT BASICInstruction manual
FR-F740-S560K-CHT TECHNICAL MANUAL
MITSUBISHI FR-F740-S560K-CHT Product information and technical parameters：
Brand: MITSUBISHI
Name: 3 phase 400V converter
Model: FR-F740-S560K-CHT
MITSUBISHI inverter FR-F740 series.
Voltage level: three phase 400V.
Frequency converter capacity: 560KW.
The main circuit of the inverter can be divided into two categories in general: voltage type is the voltage source of the DC converter for AC inverter,
The filtering of the DC circuit is the capacitance; the current mode is the DC conversion of the current source to the AC inverter,
The DC loop filter is the inductor.
Why is the frequency of the inverter voltage proportional to the change?
The electromagnetic torque of any motor is the result of the interaction between the current and the magnetic flux, the current is not allowed to exceed the rated value, otherwise it will cause the heating of the motor.
Therefore, if the magnetic flux decreases, the electromagnetic torque will decrease, which leads to the reduction of the load carrying capacity.
Power: 30kw.
Voltage: 200V.
The power factor of the input power factor is up to 0.99 and above (100% load).
Can be connected to multiple inverters, to achieve a common DC bus mode.
Equipped with standard power retrogradation function. MITSUBISHI inverter series: FR-A820.
Voltage level: three phase 200V MITSUBISHI FR-F740-S560K-CHT.
Power: 0.75kw.
SLD converter rated current: 7.7A.
Structure and function: Standard model FR-F740-S560K-CHT
Type: CA.
Substrate coating: have.
Parameters can be selected by 4 different rated current and different overload rating (SLD (ultra light load) rated, LD (light load) rating, ND (general load) rating, HD (weight).
Type load) for selection.
You can choose the most suitable frequency converter for use; and by selecting a transducer with a SLD or LD rated level,
Be able to reduce the size of the device (compared with the FR-A700 series, to reduce the volume of equipment) MITSUBISHI FR-F740-S560K-CHT.
For applications that require high torque at low speeds, the HD rating is the most suitable.
The controller is used to control and monitor the frequency converter through the network.
Standard corresponding RS-485 communication (MITSUBISHI converter protocol, Modbus-RTU protocol) data transmission speed up to 115200bps MITSUBISHI FR-F740-S560K-CHT. MITSUBISHI inverter series: FR-F820.
Voltage level: three phase 200V.
Power: 15kw.
SLD converter rated current: 77A.
Structure and function: Standard model.
Type: CA.
Substrate coating: have.
PID target value can be set directly from the operator panel. Flexible change settings.
In the 1 inverter, through the PID control of parallel connection pump (up to 4 units) can adjust the amount of water and so on.
1 pumps driven by parallel connecction of the pump machine, in addition to the pump for power frequency drive FR-F740-S560K-CHT.
The number of power frequency driven pump, according to the automatic adjustment of water.
The liquid crystal panel options (FR-LU08) can be converted too a more intuitive display unit% units FR-F740-S560K-CHT.
Through the use of wind, temperature and other familiar units can be simple to maintain and adjust the display.
Voltage: 200V.
The power factor of the input power factor is up to 0.99 and above (100% load).
Can be connected to multiple inverters, to achieve a common DC bus mode.
Equipped with standard power retrogradation function. MITSUBISHI inverter series: FR-A820.
Voltage level: three phase 200V MITSUBISHI FR-F740-S560K-CHT.
Power: 0.75kw.
SLD converter rated current: 7.7A.
Structure and function: Standard model FR-F740-S560K-CHT
Type: CA.
Substrate coating: have.
Parameters can be selected by 4 different rated current and different overload rating (SLD (ultra light load) rated, LD (light load) rating, ND (general load) rating, HD (weight).
Type load) for selection.
You can choose the most suitable frequency converter for use; and by selecting a transducer with a SLD or LD rated level,
Be able to reduce the size of the device (compared with the FR-A700 series, to reduce the volume of equipment) MITSUBISHI FR-F740-S560K-CHT.
For applications that require high torque at low speeds, the HD rating is the most suitable.
The controller is used to control and monitor the frequency converter through the network.
Standard corresponding RS-485 communication (MITSUBISHI converter protocol, Modbus-RTU protocol) data transmission speed up to 115200bps MITSUBISHI FR-F740-S560K-CHT. MITSUBISHI inverter series: FR-F820.
Voltage level: three phase 200V.
Power: 15kw.
SLD converter rated current: 77A.
Structure and function: Standard model.
Type: CA.
Substrate coating: have.
PID target value can be set directly from the operator panel. Flexible change settings.
In the 1 inverter, through the PID control of parallel connection pump (up to 4 units) can adjust the amount of water and so on.
1 pumps driven by parallel connecction of the pump machine, in addition to the pump for power frequency drive FR-F740-S560K-CHT.
The number of power frequency driven pump, according to the automatic adjustment of water.
The liquid crystal panel options (FR-LU08) can be converted too a more intuitive display unit% units FR-F740-S560K-CHT.
Through the use of wind, temperature and other familiar units can be simple to maintain and adjust the display.
...More relevant models >>>>