LK Automation Limited
Brand:
MITSUBISHI
FR-ABR-H7.5K | MITSUBISHI High frequency braking resistor FR-ABR-H7.5K
MITSUBISHI FR-ABR-H7.5K Manual And Instructions
FR-ABR-H7.5K datasheetPDF datasheet
FR-ABR-H7.5K Instruction manual
MITSUBISHI FR-ABR-H7.5K Product information and technical parameters：
Brand: MITSUBISHI
Name: High frequency braking resistor
Model: FR-ABR-H7.5K
Power: 7.5kw.
Purpose: high frequency braking resistor.
The use rate of the built-in regenerative brake of the transducer can be promoted.
When using the FR-ABR type brake resistor, the short circuit piece between the terminal PR-PX is removed. Does not remove the short circuit chip will lead to overheating of the brake resistor.
The utilization rate of the regenerative braking should be less than the allowable brake use rate in the above table.
With the operating frequency of the brake resistor to reach 300 degrees C or higher, it is necessary to take protective measures and cooling.
MYS type resistor can be used. But please pay attention to the allowable brake use rate.
Do not remove the terminal P/+ and P1 between the short circuit chip, in addition to connecting the DC reactor.
The installation of thermal relay, to avoid overheating and burn the braking resistor.
...More relevant models >>>>
FR-ABR-H7.5K datasheetPDF datasheet
FR-ABR-H7.5K Instruction manual
MITSUBISHI FR-ABR-H7.5K Product information and technical parameters：
Brand: MITSUBISHI
Name: High frequency braking resistor
Model: FR-ABR-H7.5K
Power: 7.5kw.
Purpose: high frequency braking resistor.
The use rate of the built-in regenerative brake of the transducer can be promoted.
When using the FR-ABR type brake resistor, the short circuit piece between the terminal PR-PX is removed. Does not remove the short circuit chip will lead to overheating of the brake resistor.
The utilization rate of the regenerative braking should be less than the allowable brake use rate in the above table.
With the operating frequency of the brake resistor to reach 300 degrees C or higher, it is necessary to take protective measures and cooling.
MYS type resistor can be used. But please pay attention to the allowable brake use rate.
Do not remove the terminal P/+ and P1 between the short circuit chip, in addition to connecting the DC reactor.
The installation of thermal relay, to avoid overheating and burn the braking resistor.
"MITSUBISHI inverter series: FR-A846.
Voltage level: three phase 400V.
Power: 0.75kw.
SLD converter rated current: 3.8A.
Structure and function: IP55 counterpart.
Type: CA.
Substrate coating: have.
Built in DC reactor.
Easy to operate, simple settings.
We have prepared a series of equipment and functions for you to work in any place to meet the life cycle of the product MITSUBISHI FR-ABR-H7.5K.
Allegedly, the motor power consumption accounted for about half of the total power generated by manufacturing industry consumption FR-ABR-H7.5K
How to achieve energy efficiency in the plant without affecting the productivity.
Less energy consumption and more output FR-A800 series inverter will help you to have both fish and bear''s paw"
Parameters and frequency settings can be modified in the program MITSUBISHI FR-ABR-H7.5K.
Inverter control, for example, by the input signal to trigger the operation of the inverter, based on the operation of the inverter
The status of the signal output, as well as the monitor output and so on, can be customized according to the requirements.
The control of each machine can be done separately by the frequency converter, and the control of the dispersion is also carried out MITSUBISHI FR-ABR-H7.5K.
Through combining with the real-time clock function can realize the automatic operation (in option FR-LU08). "MITSUBISHI inverter FR-F740 series.
Voltage level: three phase 400V.
Frequency converter capacity: 630KW.
The main circuit of the inverter can be divided into two categories in general: voltage type is the voltage source of the DC converter for AC inverter,
The filtering of the DC circuit is the capacitance; the current mode is the DC conversion of the current source to the AC inverter,
The DC loop filter is the inductor.
Why is the frequency of the inverter voltage proporttional to the change?
The electromagnetic torque of any motor is the result of the interaction between the current and the magnetic flux, the current is not allowed to exceed the rated value, otherwise it will cause the heating of the mmotor FR-ABR-H7 FR-ABR-H7.5K. 5K.
Therefore, if the magnetic flux decreases, the electromagnetic torque will decrease, which leads to the reduction of the load carrying capacity.
Voltage level: three phase 400V.
Power: 0.75kw.
SLD converter rated current: 3.8A.
Structure and function: IP55 counterpart.
Type: CA.
Substrate coating: have.
Built in DC reactor.
Easy to operate, simple settings.
We have prepared a series of equipment and functions for you to work in any place to meet the life cycle of the product MITSUBISHI FR-ABR-H7.5K.
Allegedly, the motor power consumption accounted for about half of the total power generated by manufacturing industry consumption FR-ABR-H7.5K
How to achieve energy efficiency in the plant without affecting the productivity.
Less energy consumption and more output FR-A800 series inverter will help you to have both fish and bear''s paw"
Parameters and frequency settings can be modified in the program MITSUBISHI FR-ABR-H7.5K.
Inverter control, for example, by the input signal to trigger the operation of the inverter, based on the operation of the inverter
The status of the signal output, as well as the monitor output and so on, can be customized according to the requirements.
The control of each machine can be done separately by the frequency converter, and the control of the dispersion is also carried out MITSUBISHI FR-ABR-H7.5K.
Through combining with the real-time clock function can realize the automatic operation (in option FR-LU08). "MITSUBISHI inverter FR-F740 series.
Voltage level: three phase 400V.
Frequency converter capacity: 630KW.
The main circuit of the inverter can be divided into two categories in general: voltage type is the voltage source of the DC converter for AC inverter,
The filtering of the DC circuit is the capacitance; the current mode is the DC conversion of the current source to the AC inverter,
The DC loop filter is the inductor.
Why is the frequency of the inverter voltage proporttional to the change?
The electromagnetic torque of any motor is the result of the interaction between the current and the magnetic flux, the current is not allowed to exceed the rated value, otherwise it will cause the heating of the mmotor FR-ABR-H7 FR-ABR-H7.5K. 5K.
Therefore, if the magnetic flux decreases, the electromagnetic torque will decrease, which leads to the reduction of the load carrying capacity.
...More relevant models >>>>