LK Automation Limited
Brand:
MITSUBISHI
A9GT-50WQBUSS | MITSUBISHI Bus connecting plate A9GT-50WQBUSS
MITSUBISHI A9GT-50WQBUSS Manual And Instructions
A9GT-50WQBUSS datasheetPDF datasheet
MITSUBISHI A9GT-50WQBUSS Product information and technical parameters：
Brand: MITSUBISHI
Name: Bus connecting plate
Model: A9GT-50WQBUSS
QCPU (Q mode) bus connection.
1 joint.
Applicable model: A956WGOT.
...More relevant models >>>>
A9GT-50WQBUSS datasheetPDF datasheet
MITSUBISHI A9GT-50WQBUSS Product information and technical parameters：
Brand: MITSUBISHI
Name: Bus connecting plate
Model: A9GT-50WQBUSS
QCPU (Q mode) bus connection.
1 joint.
Applicable model: A956WGOT.
A series of high performance models that are widely used in network or single machine work environments.
Screen size: 10.4 inches.
Display color: 256 color or more color.
Installation type: compatible with video /RGB.
Resolution: SVGA (800 x 600).
Display device: TFT color (high brightness, wide viewing angle) MITSUBISHI A9GT-50WQBUSS.
Host frame color: black.
Power type: AC100~240V.
Communication interface: with built-in RS-422 A9GT-50WQBUSS
Ideal model for high performance in a network or independent operation environment.
User storage capacity: 9MB (GT15__-VNB_:5MB).
Device USB port.
Standard RS-232 interface.
Support video /RGB unit.
If the capacitive touch screen is in the middle of the operation, the display resolution or display mode of the touch screen is changed again,
Or the refresh rate of the touch screen controller is adjusted by itself, and the cursor and the touch point can not be felt when the cursor is not corresponding to the touch point,
Must be re calibrated to the touch screen system MITSUBISHI A9GT-50WQBUSS.
In order to ensure the normal operation of the touch screen system, in addition to ensure the proper installation of the system software,
Must also remember that in a host do not install two or more than two kinds of touch screen driver,
This will cause the system to run in conflict, so that the touch screen system can not be used properly MITSUBISHI A9GT-50WQBUSS. Connecting cable for handheld GOT and PLC.
Cable length: 3 meters.
Application: RS-422 connection and RS-232C connection. Cable length: 1m.
For connection between FXCPU (MINI-DIN8 pin connector) and GOT.
Connection between FXCPU communication function extension board (MINI-DIN8 pin connector) and GOT.
Applicable models: GT10, GT21. 15 inches.
Suurface treatment: anti reflective film A9GT-50WQBUSS.
Protective film color: No.
USB protection cover parts: there is an opening.
Set number: 5.
Applicable model: GT27. Cable length: 3.0m.
For the connection between QCPU and GOT.
For connection betwween two GOT A9GT-50WQBUSS.
Applicable models: GT16, GT15, GT11, GT27, GT25. QnA/ACPU bus connection.
1 joint.
Applicable models: A985 (-V) /975/970/960/956 (W) GOT.
Screen size: 10.4 inches.
Display color: 256 color or more color.
Installation type: compatible with video /RGB.
Resolution: SVGA (800 x 600).
Display device: TFT color (high brightness, wide viewing angle) MITSUBISHI A9GT-50WQBUSS.
Host frame color: black.
Power type: AC100~240V.
Communication interface: with built-in RS-422 A9GT-50WQBUSS
Ideal model for high performance in a network or independent operation environment.
User storage capacity: 9MB (GT15__-VNB_:5MB).
Device USB port.
Standard RS-232 interface.
Support video /RGB unit.
If the capacitive touch screen is in the middle of the operation, the display resolution or display mode of the touch screen is changed again,
Or the refresh rate of the touch screen controller is adjusted by itself, and the cursor and the touch point can not be felt when the cursor is not corresponding to the touch point,
Must be re calibrated to the touch screen system MITSUBISHI A9GT-50WQBUSS.
In order to ensure the normal operation of the touch screen system, in addition to ensure the proper installation of the system software,
Must also remember that in a host do not install two or more than two kinds of touch screen driver,
This will cause the system to run in conflict, so that the touch screen system can not be used properly MITSUBISHI A9GT-50WQBUSS. Connecting cable for handheld GOT and PLC.
Cable length: 3 meters.
Application: RS-422 connection and RS-232C connection. Cable length: 1m.
For connection between FXCPU (MINI-DIN8 pin connector) and GOT.
Connection between FXCPU communication function extension board (MINI-DIN8 pin connector) and GOT.
Applicable models: GT10, GT21. 15 inches.
Suurface treatment: anti reflective film A9GT-50WQBUSS.
Protective film color: No.
USB protection cover parts: there is an opening.
Set number: 5.
Applicable model: GT27. Cable length: 3.0m.
For the connection between QCPU and GOT.
For connection betwween two GOT A9GT-50WQBUSS.
Applicable models: GT16, GT15, GT11, GT27, GT25. QnA/ACPU bus connection.
1 joint.
Applicable models: A985 (-V) /975/970/960/956 (W) GOT.
...More relevant models >>>>