LK Automation Limited LK Automation Limited
Brand Sort: MITSUBISHI
Home >> Price
Q1MEM-64SE Market price | Q1MEM-64SE Introduction
MITSUBISHI Q1MEM-64SE
Motor series: low inertia, medium and small capacity.
Using a serial absolute / incremental encoder.
Rated output power: 3.5kw.
Rated speed: 2000rpm.
With the brake: without.
Shaft end: straight shaft.
Comparison of single phase induction motor and servo motor.
The working principle of the AC servo motor is similar to that of the single phase induction motor,
But the rotor resistance of the former is much larger than that of the latter,
So the servo motor is compared with the single machine asynchronous motor,
There are three notable features:
1, large starting torque Q1MEM-64SE
2, a wide range of operation.
3, no rotation phenomenon.
AC servo motor running smoothly, low noise.
But the control characteristic is non-linear, and because the rotor resistance is big, the loss is big, the efficiency is low,
Therefore, compared with the same capacity DC servo motor, the volume is large and the weight is heavy,
So it is only suitable for 0.5-100W small power control system. Maximum transmission speed: 115.2kbps.
DC5V internal consumption current: 0.15A.
Weight: 0.12kg.
GOT connection.
MELSOFT connection.
Communication protocol support function serial communication function. Fiber length: 0.5 meters.
SSCNET III cables (standard optical fiber used in control cabinet).
Joints for CN1A and CN1B. Cable length: 3m.
(for MR-J2S- / CP (1) -S084).
For MR-J2S-11KA (4) MR-J2S-22KA to (4). Bus cables used for GOT1000 to replace the ferrite cores used in the existing GOT-A900 bus cables.
Applicable models: GT16, GT15, GT11, GT27, GT25. Input points: 32 points.
Input voltage: DC12/24V.
Current: 3/7mA.
Response time: 10ms.
Positive / negative sharing.
50 point terminal station.
System program memory for storing system program,
Including management procedures, monitoring procedures, as well as the user program to do the compiler to compile the process of interpretation.
Read only memory. Manufacturers use, content can not be changed, power does not disappear.
PLC selection with the development of PLC technology, more and more types of PLC products,
Function is becoming more and more perfect, and its application is more and more extensive.
Different series of different models of PLC has different performance, applicable occasions also have different emphasis,
Price also has a greater difference. Therefore PLC selection,
Under the premise of meeting the control requirements,
Should consider the best performance to price ratio, a reasonable choice of PLC.
Each scanning process. Focus on the input signal sampling. Focus on the output signal to refresh.
Input refresh process. When the input port is closed,
Program in the implementation phase, the input end of a new state, the new state can not be read.
Only when the program is scanned, the new state is read.
A scan cycle is divided into the input sample, the program execution, the output refresh.
The contents of the component image register are changed with the change of the execution of the program.
The length of the scan cycle is determined by the three.
CPU the speed of executing instructions.
Time of instruction.
Instruction count.
Due to the adoption of centralized sampling.
Centralized output mode.
There exist input / output hysteresis phenomena, i.e., the input / output response delay.
Q1MEM-64SE Operation manual/Instructions/Model selection sample download link: /searchDownload.html?Search=Q1MEM-64SE&select=5


...more relevant model market price >>>>
Related products
MITSUBISHI
Memory card
Q1MEM-1MSE
MITSUBISHI Memory card Q1MEM-1MSE
SRAM E2PROM memory card. RAM capacity: 5
MITSUBISHI
Memory card
Q1MEM-64S
MITSUBISHI Memory card Q1MEM-64S
SRAM memory card. RAM capacity: 64KB.
MITSUBISHI
Memory card
Q1MEM-256SE
MITSUBISHI Memory card Q1MEM-256SE
SRAM E2PROM memory card. RAM capacity: 1
MITSUBISHI
Memory card
Q1MEM-512S
MITSUBISHI Memory card Q1MEM-512S
SRAM memory card. RAM capacity: 512KB.