LK Automation Limited LK Automation Limited
Download Sort: MITSUBISHI
Home >> Manual Download
MITSUBISHI GT10-30PSCB Manual GT10-30PSCB User's Manual
Product model: GT10-30PSCB
Name: PROTECTIVE SHEET
Brand: MITSUBISHI
Sort: User's Manual
File language: English
Cable length: 3m.
The connection between the FXCPU (MINI-DIN8 pin connector) and the graphic operation terminal.
Connection between FXCPU communication function extension board (MINI-DIN8 pin connector) and GOT.
Applicable models: GT10, GT21. A series of high performance models that are widely used in network or single machine work environments GT10-30PSCB Manual GT10-30PSCB User's Manual.
Screen size: 5 GT10-30PSCB7 inches.
Display color: monochrome.
Mounting type: panel mounting type.
Resolution: QVGA (320 x 240).
Display device: STN monochrome.
Host frame color: black.
Power type: DC24V.
Communication interface: with built-in RS-422.
Ideal model for high performance in a network or independent operation environment.
User storage capacity: 9MB (GT15__-VNB_:5MB) GT10-30PSCB Manual GT10-30PSCB User's Manual.
Device USB port.
Standard RS-232 interface.
Support video /RGB unit.
If the capacitive touch screen is in the middle of the operation, the display resolution or display mode of the touch screen is changed again,
Or the refresh rate of the touch screen controller is adjusted by itself, and the cursor and the touch point can not be felt when the cursor is not corresponding to the touch point,
Must be re calibrated to the touch screen system GT10-30PSCB Manual GT10-30PSCB User's Manual.
In order to ensure the normal operation of the touch screen system, in addition to ensure the proper installation of the system software,
Must also remember that in a host do not install two or more than two kinds of touch screen driver,
This will cause the system to run in conflict, so that the touch screen system can not be used properly. Cable length: 30m.
For connection between FXCPU (MINI-DIN8 pin connector) and GOT.
Connection between FXCPU communication function extension board (MINI-DIN8 pin connector) and GOT.
Applicable models: GT10, GT21. For GT1030/GT1020 (used for operating system project data transfer) without power supply.
Applicable model: GT10. Protective film for 8.4 inch screen.
Transparent, 5.
Applicable model: GT16. 128MB flash ROM.
Applicable models: GT16, GT15, GT11, HandyGOT. Series: multimedia and advanced features and features of a variety of high-performance models.
Screen size: 6.5 inches.
Display color: 256 color or more color.
Installation type: hand held.
Resolution: VGA (640 x 480).
Display device: TFT color (high brightness, wide viewing angle).
Host frame color: black.
Power type: DC24V.
Communication interface: with built-in RS-422.
High performance models with multimedia and advanced features and functionality (including embedded communications capabilities).
User storage capacity: 15MB (GT16__-VNB__:11MB).
With HOST USB and device USB port.
Standard Ethernet, RS-422/485 and RS-232 ports.
Support multimedia and video /RGB units.
Analog touch panel.
Do not let the touch screen surface with water drops or other soft things stick to the surface,
Otherwise, the touch screen is easy to mistake that there is a hand touch caused by surface acoustic wave screen is not allowed.
In addition to cleaning the dirt on the surface of the touch screen,
You can use a soft dry cloth or a cleaning agent to clean out the center of the screen carefully,
Or use a dry soft cloth dipped in industrial alcohol or glass cleaning fluid to clean the touch screen surface.
Touch screen response is slow if you use a hand or other touch to touch the surface acoustic wave touch screen,
This shows that it is likely that the touch screen system has been obsolete, the internal clock frequency is too low,
Or because there is water in the surface of the touch screen to make the touch screen mobile, rapid response recovery,
To replace or upgrade the system must, or use dry cloth touch screen on the surface of the water GT10-30PSCB Manual GT10-30PSCB User's Manual.
If the user is operating the touch screen, the direction of the touch move is to the left,
But the cursor of the system moves to the right,
The failure may be due to the conneection of the control box and the touch screen connected to the connector or the touch screen,
Users as long as the direction of the re exchange of it GT10-30PSCB Manual GT10-30PSCB User's Manual.
Related products
MITSUBISHI
Resist film
GT16-70PSCB
MITSUBISHI Resist film GT16-70PSCB
Protective film for 10.4 inch screen. Tr
MITSUBISHI
Oil resistant cap
GT10-30PCO
MITSUBISHI Oil resistant cap GT10-30PCO
Oil resistant cap for 4.5 inch screen. A
MITSUBISHI
GT10 storage board
GT10-50FMB
MITSUBISHI GT10 storage board GT10-50FMB
For the GT105 - /GT104 - operating syst
MITSUBISHI
USB cable
GT10-RS2TUSB-5S
MITSUBISHI USB cable GT10-RS2TUSB-5S
For connection etween personal computer